6 Things On Home Improvement Plumbing

TL:DR? It is important for drains to be properly vented to ensure efficient flow of water and air and prevent sewage and sewer gases from entering going back into the home. Plumbing for sinks in kitchen islands. While most of the time fixtures require the vent to go remain verticals up for a minimum of 6-inches above the flood level of the fixture, an exception is made for fixtures in islands where it would not be possible. In islands a loop vent is often used. In some situations people just use an Air Admittance Valve (AAV) but they are prohibited in some jurisdictions and can have mechanical failure. After the trap and a sufficient trap arm, a sanitary tee is attached to send the waste down and the vent up. Then some 45degree elbows are used to create a loop vent which should have a cleanout above the floor level. The vent under the floor needs to go up into the nearest wall.

https://plumbingcodestuff.tumblr.com/post/147933840818/randomsudoisms-plumbing-code-updates-2013#_=_

With a little planning and insight from industry experts, you can prevent yourself from holiday hassles. Here are the top four tips from The Sunny Plumber to keep your pipe dreams in check. What’s the No. 1 issue consumers need to think about around the holidays to keep their plumbing working? One of the most common plumbing issues people face during the holidays is a clogged sink or malfunctioning garbage disposal. I always recommend being wary of the “FOG.” Fats, oils, and grease are your garbage disposals worst enemy. While this material is in liquid form when it’s initially poured into the disposal, it congeals into a viscous sludge as it cools. The FOG then sticks to the walls of the disposal chamber, as well as the walls of the drain pipe. This can gum up the impeller, as well as clog the drain. Don’t pour FOG down the garbage disposal if you want to avoid these issues.

http://www.thesunnyplumber.com/blog/drain-and-sewer-service/prevent-holiday-plumbing-nightmares/

These monsters required Popeye forearms and a diet of canned spinach to operate, but they could cut through anything and were virtually indestructible. The DeWalt 60-volt MAX circular saw (model DCS575T2) is the cordless equivalent of these vintage brutes. Gordontheplumber.com Clogged Drain naperville il It has a lot to love. Like all worm-drive saws, the left-side blade position makes it easy to see your cutting line. It’s a workhorse: The 60-volt battery coupled with DeWalt’s thin-kerf FLEXVOLT blade (specifically designed for cordless saws) creates a saw that’s fast and powerful. It can churn through materials up to 2-1/2 in. thick and cut bevels up to 53 degrees. The safety button is easy to access. The saw also has some nice grace notes, like the on-board blade-changing wrench, a depth gauge that tells you how deep the blade is set, and a carrying bag. The swing-down rafter hook lets you hang the saw from a joist or rafter between cuts (and believe me, you’ll want to give your arm a break between cuts). The DeWalt Fast Charger is so hardworking that it’s fan cooled.

https://www.familyhandyman.com/stuff-we-love/why-we-love-the-dewalt-60-volt-max-circular-saw/

As they were leaving one of the firefighters came over to me and said: “you saved this ladies house”. Kind words indeed, but I was visibly shaken as nothing like that had never happened to me before. This is one of the times when you thank god your liability insurance is paid up and in good standing. Although this was six attached condominiums and my limits at that time would never have covered a complete loss! I took a long lunch break came back and finished soldering on the cold water valve, followed by a thorough cleaning of the bathroom. The following day I sent my tile man to the house to re-insulate and patch the wallboard, followed by painting the entire bathroom. An experience I will never forget nor take for granted when using an open flame inside or outside of a wall. All it takes is one stray spark to get away and your life could change forever. How To Solder Copper Tubing & Avoid a Disaster!

http://www.bobsplumbingvideos.com/copper-tubing/

As always, PlumbingSupply.com® wishes you a safe and happy New Year! Water is one of our most precious natural resources – we can’t live without it, and yet there’s a very limited supply. If you’re thinking of doing a kitchen, bath or laundry room remodel this year, choose water-efficient faucets and shower heads, and/or place a point-of-use water heater in areas where you consistently run the taps to heat water up. Outdoors, you can install a drip-irrigation system instead of a new sprinkler or consider setting up your own rainwater harvesting system to use for watering plants or washing your car. It can be helpful to think of your toilet as another appliance in your home. Anything with moving parts can break or wear down – and that includes the moving parts of your toilet. Save water and avoid costly problems later with good maintenance this year. Ideally, your water heater should last between 10 and 15 years, but without proper maintenance many fail after 5 or 6 years, leaving you frustrated and sometimes causing significant damage to your home. An annual flush and all-around check to make sure all the parts are functioning well can help you avoid cold showers, save you money, and extend the life of your water heater. Nobody wants to deal with the hassle (and often major expense) associated with clogged drains.

https://theplumber.com/5-easy-new-years-plumbing-resolutions/

You may also be interested to read